State whether the following statements are True or False. Give reason in support of your
(a) Statistical quality control (SQC) is a technique of process control only.
(b) Twenty pieces of different length of cloth contained 2, 4, 1, 3, 5, 4, 2, 7, 3, 5, 2, 2, 4, 5,6, 4, 2, 1, 2, 4 defects respectively. To check the process is under control with respect to the number of defects, we should use np-chart.
(c) If the probabilities are not associated with the occurence of different states of nature, then the situation is known as decision making under risk.
(d) In single sampling plan, if we increase acceptance number then the OC curve will be steeper.
(e) A system has four components connected in parallel configuration with reliability 0.4, 0.5, 0.8 To improve the reliability of the system most, we have to replace the component which reliability is 0.2.
(a) False. Statistical Quality Control (SQC) includes both process control and product control. Process control is managed through control charts, while product control is ensured through acceptance sampling techniques.
(b) False. Since we are dealing with the number of defects per unit (length of cloth), the appropriate control chart to use ___ _______ ____ __________ __________ _________ _______.
_________ ________ ___ __________ ________ ______ _______.
________ _________ ____ ______ _________ ____ _______ _____.
__________ ____ ___ ________ _____ ____ ____ _____ ______ _________ _________.
_________ ____ _____ ____ _______ __________ _____ __________ _________ __________ _______.
___ _________ ________ __________ _______ ___.
________ ___ _____ ___ _____ _______ ____ __________ _________ ____ ___ _____.
______ ____ ________ ___ __________ ________ ________ ______ ____ ___ _____ _______.
_________ _________ _________ ___ _____ _______ __________ _________ __________ ___ ____.
_________ _________ ___ ______ _________ _____ ______ ____.
__________ _____ ________ ______ ____ ______ _______ __________.
__________ _______ __________ _________ _________ ______ ______ __________.
____ __________ ________ _______ ______ _________ _________ ___.
______ _________ _____ ___ ________.
___ __________ ____ __________ ______ _____ ____.
_____ _________ ___ ______ ______ ____ _________ ____ _____ ____ ______.
___ ___ ________ _______ ______ ___.
_____ ______ ____ _________ ____ ________ __________ ______ ___ _______.
___ ________.
Get Full Answer on WhatsApp
An office supply company ordered a lot of 400 printers. When the lot arrives the company inspector will randomly inspect 12 printers. If more than three printers in the sample are non-conforming, the lot will be rejected. If fewer than two printers are non-conforming the lot will be accepted. Otherwise, a second sample of size 5 will be taken. Suppose the inspector finds two non-conforming printers in the first sample and two in the second saraple. Also AQI. and LTPD at 0.05 and 0.10 respectively. Let incoming quality be 4%
i) What is the probability of accepting the lot at the first sample?
ii) What is the probability of accepting the lot at the second sample?
iii) Find AQL and ATI
A manufacturer of men's jeans purchases zippers in lots of 500. The jeans manufacturer uses single-sample acceptance sampling with a sample size of 10 to determine whether to accept the lot. The manufacturer uses 2 as the acceptance nuraber. Suppose 3% nonconforming zippers are acceptable to the manufacturer and 8% oncoming zippers are not acceptable. Let incoming quality be 4%
i) Construct an OC carve
ii) Average outing quality (AOQ), if the rejected lots are scromed and all defective zippers are replaced by non-defectives
i) Average total inspection (ATI).
At a call omtre, callers have to wait till an operator is ready to take their call. To monitor this process, 5 calls were recorded every hour for the S-hour working day. The data below shows the waiting time in seconds:
| Time | Sample Number | ||||
| 1 | 2 | 3 | 4 | 5 | |
| 9 a.m | 8 | 9 | 15 | 4 | 11 |
| 10 | 7 | 10 | 7 | 6 | 8 |
| 11 | 11 | 12 | 10 | 9 | 10 |
| 12 | 12 | 8 | 6 | 9 | 12 |
| 1 p.m. | 11 | 10 | 6 | 14 | 11 |
| 2 | 7 | 7 | 10 | 4 | 11 |
| 3 | 10 | 7 | 4 | 10 | 10 |
| 4 | 8 | 11 | 11 | 11 | 7 |
State whether the following statements are True or False. Give reason in support of your
(a) Statistical quality control (SQC) is a technique of process control only.
(b) Twenty pieces of different length of cloth contained 2, 4, 1, 3, 5, 4, 2, 7, 3, 5, 2, 2, 4, 5,6, 4, 2, 1, 2, 4 defects respectively. To check the process is under control with respect to the number of defects, we should use np-chart.
(c) If the probabilities are not associated with the occurence of different states of nature, then the situation is known as decision making under risk.
(d) In single sampling plan, if we increase acceptance number then the OC curve will be steeper.
(e) A system has four components connected in parallel configuration with reliability 0.4, 0.5, 0.8 To improve the reliability of the system most, we have to replace the component which reliability is 0.2.
A system has seven independent components and reliability block diagram of it shown blow:
Find reliability of the system.
A two-person zero-sum game having the following payoff matrix for player A
(i) Check whether saddle point exit or not.
(ii) If saddle point does not exit then determine optimal strategies for both the manufacturers and value of the game.
The failure data for 40 electronic components is shown below:
| Operating Time (in hours) | 0-5 | 5-10 | 10-15 | 15-20 | 20-25 | 25-30 |
| Number of Failures | 5 | 7 | 6 | 4 | 5 | 4 |
| Operating Time (in hours) | 30-35 | 35-40 | 40-45 | 45-50 | ≥50 | |
| Number of Failures | 4 | 0 | 2 | 1 | 2 |