A system has seven independent components and reliability block diagram of it shown blow:
Find reliability of the system.
To find the reliability of the system, we need to analyze the given reliability block diagram. Since the diagram is not provided, let's consider two possible cases:
### Case 1: Series System
If all seven components are connected in series, _______ ____ ____ _________ ___.
____ __________ ____ _______ ______ _________ _________ ________.
________ ______ _________ ________ _____ ____ __________ __________.
________ ______ __________ _____ ___ _____ ______ ____.
_________ ______ _________ ______ _______ __________.
________ __________ _____ ____ _____ ______.
_______ _________ __________ _____ ____.
_________ _______ __________ _________ _____ ________.
_______ ____ ____ _____ ____.
_____ _____ ____ ___ ____.
________ _______ ___ ________ ________ _______ ____ ____ ___ _________ ____.
________ _______ ___ _____ ___.
______ _______ ________ _________ ______ ________ ________.
______ ________ ___ ________ ___ ______ ____ _________.
___ _____ _____ ___ __________ _________ __________ ________ ________ _________ _____ _____.
_______ _____ __________ ___ ____ _________ _________ ________ ______ _____.
________ _________ _________ ______ ____.
__________ ____ __________ ________ __________ _____ _________ _________ _________ ____.
_____ ____ ________ _____ _____ ______ ______ _________.
_________ _______ ____ ____ ___ ________.
______ _________ _________ ____ __________ ________ _____ ___ _____.
________ _____ ____ ____ ______ __________ ____ ____.
________ _________ ________ _________ __________ ____.
______ ___ _____ _________ _____.
________.
Get Full Answer on WhatsApp
A system has seven independent components and reliability block diagram of it shown blow:
Find reliability of the system.
The failure data for 40 electronic components is shown below:
| Operating Time (in hours) | 0-5 | 5-10 | 10-15 | 15-20 | 20-25 | 25-30 |
| Number of Failures | 5 | 7 | 6 | 4 | 5 | 4 |
| Operating Time (in hours) | 30-35 | 35-40 | 40-45 | 45-50 | ≥50 | |
| Number of Failures | 4 | 0 | 2 | 1 | 2 |
An office supply company ordered a lot of 400 printers. When the lot arrives the company inspector will randomly inspect 12 printers. If more than three printers in the sample are non-conforming, the lot will be rejected. If fewer than two printers are non-conforming the lot will be accepted. Otherwise, a second sample of size 5 will be taken. Suppose the inspector finds two non-conforming printers in the first sample and two in the second saraple. Also AQI. and LTPD at 0.05 and 0.10 respectively. Let incoming quality be 4%
i) What is the probability of accepting the lot at the first sample?
ii) What is the probability of accepting the lot at the second sample?
iii) Find AQL and ATI
Twenty saraples each of size 10 were inspected. The number of defectives detected in cach of them is given below: : 0, 1, 0, 3, 9, 2, 0, 7, 0, 1, 1, 0, 0, 3, 1, 0, 0, 2, 1, 0 Find the control limits for the number of defectives and establish quality standards for the future. Plot the graph and interpost.
A two-person zero-sum game having the following payoff matrix for player A
(i) Check whether saddle point exit or not.
(ii) If saddle point does not exit then determine optimal strategies for both the manufacturers and value of the game.
State whether the following statements are True or False. Give reason in support of your
(a) Statistical quality control (SQC) is a technique of process control only.
(b) Twenty pieces of different length of cloth contained 2, 4, 1, 3, 5, 4, 2, 7, 3, 5, 2, 2, 4, 5,6, 4, 2, 1, 2, 4 defects respectively. To check the process is under control with respect to the number of defects, we should use np-chart.
(c) If the probabilities are not associated with the occurence of different states of nature, then the situation is known as decision making under risk.
(d) In single sampling plan, if we increase acceptance number then the OC curve will be steeper.
(e) A system has four components connected in parallel configuration with reliability 0.4, 0.5, 0.8 To improve the reliability of the system most, we have to replace the component which reliability is 0.2.
A manufacturer of men's jeans purchases zippers in lots of 500. The jeans manufacturer uses single-sample acceptance sampling with a sample size of 10 to determine whether to accept the lot. The manufacturer uses 2 as the acceptance nuraber. Suppose 3% nonconforming zippers are acceptable to the manufacturer and 8% oncoming zippers are not acceptable. Let incoming quality be 4%
i) Construct an OC carve
ii) Average outing quality (AOQ), if the rejected lots are scromed and all defective zippers are replaced by non-defectives
i) Average total inspection (ATI).